Existe-t-il des preuves quantifiables du cycle d'alimentation d'un routeur pendant 10 secondes?

Table des matières:

Existe-t-il des preuves quantifiables du cycle d'alimentation d'un routeur pendant 10 secondes?
Existe-t-il des preuves quantifiables du cycle d'alimentation d'un routeur pendant 10 secondes?

Vidéo: Existe-t-il des preuves quantifiables du cycle d'alimentation d'un routeur pendant 10 secondes?

Vidéo: Existe-t-il des preuves quantifiables du cycle d'alimentation d'un routeur pendant 10 secondes?
Vidéo: How to Remove Device From Amazon Alexa - YouTube 2024, Mars
Anonim
Nous avons tous entendu le conseil concernant le cycle d'alimentation d'un dispositif électronique afin de résoudre les problèmes, mais le cycle d'alimentation est-il préférable à un simple débranchement et rebranchement du périphérique? L’article d’aujourd’hui sur le SuperUser Q & R répond aux questions d’un lecteur curieux.
Nous avons tous entendu le conseil concernant le cycle d'alimentation d'un dispositif électronique afin de résoudre les problèmes, mais le cycle d'alimentation est-il préférable à un simple débranchement et rebranchement du périphérique? L’article d’aujourd’hui sur le SuperUser Q & R répond aux questions d’un lecteur curieux.

La séance de questions et réponses d’aujourd’hui nous est offerte par SuperUser, une sous-division de Stack Exchange, un groupe de sites Web de questions-réponses dirigé par la communauté.

Photo fournie par Ben Daines (Flickr).

La question

Lecteur superutilisateur cqm veut savoir s’il existe des preuves quantifiables soutenant les dispositifs électroniques à cycle d’alimentation au lieu de simplement les débrancher et les rebrancher:

Is there any quantifiable evidence to support power cycling routers for 10 seconds (or any arbitrary amount of time) instead of just unplugging and plugging them back in?

This is related to troubleshooting a misbehaving router. The theory is based on ‘things’ needing to be cleared from memory and that this could take a few seconds. This is also a theory related to electronics from over a decade ago, and I am sure it was equally as anecdotal then.

As a person allergic to anecdotes, I became curious when I realized that I had never investigated this issue. Is there any quantifiable reason to support power cycling routers for 10 seconds (or any arbitrary amount of time) instead of just unplugging and plugging them back in?

Existe-t-il des preuves quantifiables soutenant les dispositifs électroniques à cycle d'alimentation électrique par rapport au simple débranchement / rebranchement?

La réponse

Les contributeurs de SuperUser, Enis P. Aginic et Wes Sayeed, ont la réponse pour nous. Tout d'abord, Enis P. Aginic:

Yes, there is. Any electronics device will have capacitors that will store energy even after you unplug it. You may have noticed that when you unplug a monitor or TV, the little diode will take another second or two to discharge remaining energy from the capacitors in the form of electricity and stop glowing.

This residual energy may not allow memory chips to wipe and you may have problems once your router starts again.

As for sources, well it is really common sense to someone with basic electronics knowledge, like the sky is blue and water is wet, so I recommend reading about capacitors to see what they do and you will understand it.

The point is that electronics components are far from perfect and any interference may produce unpredictable results.

Suivi de la réponse de Wes Sayeed:

Ten seconds is an arbitrarily long amount of time, but yes, it does take time for electronic devices to discharge themselves completely because of the capacitance of the circuits within. Some of this capacitance is intentional, some of it is not.

It is impossible to say exactly how much time is needed, as the bleed-off of that capacitance varies with environmental factors like temperature, humidity, and background EMI generated by nearby electronics. The RAM in your computer, for example, can take minutes to fully discharge.

But there is a shortcut. If the router has a button of any kind on it (WPS button or a reset button), this will usually discharge any residual electrical charge immediately. This is because the button places a load on the circuit(s) holding the charge and there is no power going into the device.

In fact, in the old days of parallel ports, this used to be a guaranteed way to correct a stubborn printer. Unplug the printer, unplug the computer, and unplug the parallel cable. Then hit the power button on both devices. Then plug everything back in. Worked every time. Parallel SCSI busses had this problem too sometimes.

Avez-vous quelque chose à ajouter à l'explication? Sound off dans les commentaires. Voulez-vous lire plus de réponses d'autres utilisateurs de Stack Exchange doués en technologie? Découvrez le fil de discussion complet ici.

Conseillé: